|
|
|
|
Part Number: EL49ICA
Compatible With: ELCO 4" MR16 Trims. Sold Separately!
Wattage - 50w Max. Voltage - 120v Bulb Type - MR16 GU-10 LED/Halogen (not included) Dimming - Based on Lamp
Height - 7 1/4" Length - 12 1/8" Width - 7 3/4"
- Double Wall IC Construction, for use in insulated ceilings, for use in IC and non-IC conditions
- Housing adjusts in frame to accommodate up to 1 1/4" ceiling thickness
- Dimmability based on lamp
- Lamp Holder: MR16 GU10 socket
- Trims and inserts sold separately
- 3 year factory warranty (limited)
- UL Listed for Damp Locations/Wet Locations with select trims
- UL Listed for Direct Contact with insulation and Combustible materials
- UL Listed for Feed Through
- Airtight per ASTM E-283
- Install a JA8-2016-E lamp/luminaire for Title 24 compliance
-
-
-
-
-
- Tech Specs
-
| -
-
-
|
-
-
-
| -
-
| -
-
-
Material | -
Steel Housing/Stamped Galvanized Steel Frame | -
-
-
- Construction Type
-
| -
- Airtight-New Construction
| -
-
-
Hanger Bars | -
- Spans Up To 24" And Can Be Repositioned 90°
-
| -
-
-
Voltage | -
120V | -
-
-
- Warranty
-
| -
3 Year Factory Warranty (limited)-
| -
-
-
- Knockouts
-
| -
Seven (7) 1/2" Trade Size Conduit Knockouts, Four (4) 3/4" Knockouts With Pry-Out Knockout Slots, , Four (4) Romex Pry-Outs With Strain Relief | -
-
-
- Approval Type
-
| -
UL - Damp Locations, UL - Wet location (with Select Trims), UL Listed - Feed Through wiring, UL - For Direct Contact and Combustible Material, Airtight Per ASTM E-283, Install A JA8-2016-E Lamp For Title 24 Compliance | -
-
-
- Recessed Size
-
| -
4"-
| -
-
-
- Wattage
-
| -
50 Watt Max. | -
-
-
Bulb Type | -
GU10 MR16 LED/Halogen | -
-
-
Dimmability
| Based On Lamp Choice | -
-
-
-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Features
Construction/Installation ▪ Double Wall IC Rated for direct contact with insulation, for use in IC and non-IC conditions. Suitable for T-grid and drop ceiling applications. ▪ Housing adjusts in frame to accommodate up to 1 1/4" ceiling thickness. Airtight housing with gasket to restrict airflow in accordance with ASTM E-283 air-tight requirements. ▪ Lamp: 50W Max.,120V, MR16 GU10 LED/Halogen (Not Included). Lamp Holder: MR16 GU10 Socket. Steel Housing for greater heat dissipation. ▪ Designed for ceiling plenums where 2x6 joists or taller are used. Steel housing. Stamped Galvanized steel frame.
Junction Box ▪ Positioned to accommodate straight conduit runs. Junction box is accessible from below the ceiling. ▪ Seven (7) 1/2" trade size conduit knockouts, Four (4) 3/4" knockouts with pry-out knockout slots, Four (4) Romex pry-outs with strain relief. ▪ See installation sheet for detailed information
Hanger Bars / New Construction ▪ Pre-installed hanger bars with True Nail facilitate easy installation in regular lumber, engineered lumber, and laminated beams. Maximum Hole cutout is 4 1/4". Access above the ceiling is NOT required for servicing and repairs occuring after installation. ▪ Integral T-bar slots for easy installation in T-bars. Spans up to 24" and can be repositioned 90°. Score lines allow for tool-free hanger bar size reduction. Integral leveling flange allows for single-person installation while aligning the housing with joists.
Electrical ▪ Input Voltage: 120VAC. Thermally protected against improper lamping.
Dimmability ▪ Based on lamp selection.
Compatible Trims ▪ Compatible with - ELCO 4" MR16 Trims. Lamp: Designed for use with GU10 MR16 LED/Halogen: Sold Separately!
Listing ▪ UL Listed for Damp Locations. UL Listed Wet Location with select trims, UL Listed for Feed Through ▪ Airtight per ASTM E-283. Install a JA8-2016-E Lamp/Luminaire for Title 24 Compliance ▪ UL Listed for Direct Contact with Insulation and Combustible Materials.
|
|
|
|
|
|
|